Parts

- Aheadset preload adjusting bolt

All-City replacement bolts and adjustment springs for the Hennepin Bridge and Space Horse dropouts. - Sold as a pair; two bolts and two springs - M4x0.7mm thread - Length: 45mm

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

The squeeze of our levers is what dreams are made of (and you know which dreams we're talking about). Most of our levers can be swapped to be run either front or rear, which is convenient if you like to your brakes reversed and a Godsend if you bust a lever in the middle of the woods. Avid levers are easy to install, simple to set up, and a pleasure to pull. - Reach Adjustment - Qwik-Adjust Barrel Adjuster - Compatible with mechanical disc brakes and linear-pull brakes

To keep your Avid brakes functioning properly, check your pads for wear and replace them when necessary. Organic compound pads are softer for quieter braking and increased modulation, while metallic pads dissipate heat better and last a bit longer. Two pads, one retraction spring and a mounting bolt are included (enough for one brake) in each pad set. And, choose an aluminum backing plate if you're really counting the grams.

Clean up your handlebar with Avid's MatchMaker X clamp. It combines mounts for your SRAM shifters and Avid brake levers into one simple, sleek unit so you can shed grams and keep your bars nice and tidy. You can also integrate RockShox's XLoc remote (sold separately) for maximum convenience and ease of use.

Clean up your control center with Avid's Matchmaker clamp. It combines the mounts for your SRAM shifters and Avid brake levers into one simple, sleek unit so you can drop some grams and keep your bar nice and tidy.

Cost effective stopping power from the leader in cable-actuated disc brakes. - All calipers have 74mm mounting bolt spacing - For use with with long cable-pull levers - Mono-block caliper design has outboard pad adjustment - Spring tension is adjustable - Includes steel-backed organic pads - Brake Caliper Type: Post Mount - Brake Lever Actuation: Long Pull - Rotor Included: No - Weight: 215 g

Need a replacement line for your Avid hydraulic disc brakes? You're covered with Avid's Hydraulic Line Kit. It's got 2000mm of hose for front or rear application, and all the fittings to work with your brakes.

Clean up your handlebar with Avid's MatchMaker X clamp. It combines mounts for your SRAM shifters and Avid brake levers into one simple, sleek unit so you can shed grams and keep your bars nice and tidy. You can also integrate RockShox's XLoc remote for maximum convenience and ease of use.

Extruded and CNC-machined from 6061-T6 aluminum, Box Two™ Stem Spacer Kits feature a lightweight design. Weights range from 0.24 to 0.29 ounces (6.7 to 8.2 grams), depending on the size. Sold in packs of five, each set provides spacing adjustments from 1 to 20 millimeters. FEATURES - Lightweight Design - Adjustment options from 1 to 20 millimeters - Fits 1" or 1-1/8" Steerer Tubes and Standard 22.2mm Handlebars SPECIFICATIONS - Inner (Ø) 1" or 1-1/8" - Height 1mm, 3mm, 5mm, 10mm 1mm, 3mm, 5mm, 10mm - Material 6061-T6 Aluminum 6061-T6 Aluminum - Weight 6.7 grams / 0.24 ounces 8.2 grams / 0.29 ounces

Box One 7075 Alloy Chainring bolt kits include five 8.5-mm front bolts, five 6-mm front bolts, and five 5-mm rear nuts, so they will fit just about any chainring/crank combination, including those with threaded holes.

The Box Three Prime 9 cassette is a great all-around cassette option. All cogs are stamped from steel and subsequently, the larger ones are pinned to alloy spiders. It also features weight-reducing holes on the cogs. - The Box Three Prime 9 offers ultra-wide ratio with consistent progressions - Prime 9 technology offers the same range as a 12-speed drivetrain, with fewer gears to shift through - Fewer parts, reduced weight, and increased durability - Cogs pinned to lightweight spiders - Constructed using a standard freehub body (HG) - Cassette Body Type: Shimano/SRAM 8, 9, 10 Speed - Drivetrain Speeds: 9 - Designed for ebike: Yes - Color: ED Black

The Box Three Rear Derailleur simplifies the features found on the Prime 9 Box One and Two rear derailleurs making for a fully featured wallet friendly rear derailleur. Including a Limited Slip Clutch, Sealed bearing pulleys and a solid construction Box Three Rear derailleurs are compatible with 11-46 and 11-50t derailleurs making it one of the most versatile derailleur offerings for Prime 9.

3 years of REVIVE out in the market resulted in another benchmark product for BikeYoke: REVIVE 2.0. The new extralong 213mm REVIVE required a lot of re-thinking and re-engineering the whole chassis structure and since we think they deserve it, the shorter REVIVES will also get all the nice updates, and benefit from what was originally implemented only for the longest sibling of the REVIVE family. Noteworthy updates of the REVIVE 2.0 include: - One piece 3D-forged upper tube unit for improved stiffness and strength - Fully hard-anodized pin seats in the upper tube for improved corrosion-resistance - CNC-finished actuation lever for even smoother engagement - New upper saddle clamp and saddle bolts with integrated conical washers for even simpler saddle installation Wanna know more about the REVIVE? What if there was a dropper post, that actually solves and not just improves reliability issues, saves cost and time on the long run, and does not let you worry about too much time spent at service-centers? Or how about “bleeding” your seat post within a few seconds, while it is still installed in your bike? BikeYoke presents the REVIVE dropper post, featuring one of the most brilliant design features in dropper post design in many years. More than 10 years of experience in drop-post design went into the “REVIVE” and the development has finally paid off. Of, course, just as many other companies, BikeYoke would say, that REVIVE is reliable and strong and smooth. And yes, REVIVE is all of that, but not because we tried to improve current designs, but because we were thinking outside of the box and created a new concept, that is completely different from everything before. To understand the benefits over other posts you have to know about the problems of many current designs first. Many of the popular current seatpost designs are based on a hydraulic lockout-system that relies on a perfectly sealing IFP (Internal Floating Piston), separating oil from air to prevent the seatpost from getting sagging or bouncing. There are a lot of difficulties to overcome when using an IFP because an IFP has to maintain 100% sealing function. If air could go to the oil side, your post will start becoming springy. This happens to a lot of posts in the market already and is the main issue why posts need to be serviced. That´s why BikeYoke´s “REVIVE” features a NON-IFP design, because we think it is too difficult - if not impossible - to make a really reliable design using an IFP. REVIVE only requires 2 dynamic seals in the hydraulic circuit: The shaft sealing and the main piston sealing for the lockout mechanism. The highly critical IFP has been removed, and with it the need of perfect concentricity and finish of the sealing surfaces of the tubes. The lack of an IFP also results in the smoothest action you can think of. The most important and ground-breaking feature of Revive is its “REVIVE-VALVE”. Even REVIVE can get air somewhere where it does not belong. This can happen for example when you actuate your seatpost while its upside down. And here is where the patented RESET VALVE comes into play: - Insert a 4mm Hex Key into the REVIVE hex port, turn it and push down the post by hand. - This will reset your hydraulic circuit on the fly - whenever. wherever. This is done just within a few seconds and only by the turn of a 4mm Allen key or the integreated mini reset lever, that comes with the post - of course without even having to remove your drop post from your bike. So, now one might already understand that: - No external air will want go inside the post´s hydraulic circuit, since it is charged with higher pressure, than its surroundings. - No oil will go out (or at least very very little oil over the curse of a long time), because of very stable sealing - external sealing has never been a real problem of current post design - The hydraulic system can be reset to “new” via the unique “REVIVE-valving” - This means the hydraulic circuit is a very stable closed system and basically maintenance free. Still there are parts that will need to be serviced sooner or later and when designing REVIVE it was put a lot of attention to maximum user-friendly serviceability: - Bushings and keyway pins will wear over time. Usually, the pins wear first and you would want to replace them to reset your rotational play. - Exchanging the pins and the lower bushing is simple and does not require any opening of the hydraulic system and can be done within less than 5 minutes. 1 set REVIVE dropper post includes: - 1x REVIVE Seatpost - 1x cable housing 1500mm - 1x inner wire 1700mm - 2x housing endcap - 1x barrel cable clamp - 1x air valve adapter - 1x Quick-Reset-Lever - 1x remote (optional) - 1x BikeYoke I-spec adapter or Splits Clamp (optional) - 1 set titanium saddle bolts and nuts (optional)

Squatch platform pedals have a low-profile, nylon construction and molded traction studs that are easier on the shin in the event of a crash or pedal slip. - EPB bearing system - Spindle size: 9/16-inch

For smooth shifting and a quiet drivetrain, pick up Campagnolo's Chorus 11-speed chain. It's unidirectional for unparalleled function and features lightweight hollow pins as well as an anti-friction treatment for shifting perfection. It also boasts excellent wear and flex resistance.

Record chains represent Campagnolo's highest quality and performance chains and are available in 9, 10 and 11 speed versions. - Hollow pins for reduced weight - NI-PTFE antifriction treatment reduces friction for smooth pedaling, reduced noise, greater efficiency and longer chain life - Links (links): 114 - Width: 5.9 mm - Drivetrain Speeds: 10 - Chain Connection Type: Pressed Pin - Half Link Chain: No - Weight: 255 grams

Campagnolo's Record 11-Speed Chain is the right choice for Campagnolo 11-speed drivetrains. This fine chain is engineered for excellent strength, long wear and brilliant shifting thanks to a unidirectional design and an anti-friction treatment that lets it glide across your cassette. It also boasts hollow pins to keep your bicycle as light as possible.

- Stock for 07-08 Record and Chorus 10-speed compact and standard cranksets - Ultra-Drive ESP alloy chainrings with anti-friction treatment and ramps/pins - *Campagnolo compact rings are Ultra-Torque specific BCD - Color: Grey

Campagnolo's Chorus Cassette offers precise, fluid shifting for your 11-speed drivetrain. The teeth have been exquisitely engineered and machined from steel, then coated with a nickel-chrome surface treatment and mounted on an aluminum carrier for flawless shifts and excellent durability.

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Durable steel construction

Cane Creek ZN40-Bearing 41.8mm 45 x 45 Zinc, Each from Cane Creek.

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 30mm (1-1/8") straight steerer tubes - Lightweight aluminum construction - Allows the installation of a straight steerer fork without changing out the headset lower

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 40mm (1-1/2") tapered steerer tubes - Durable steel construction

Cane Creek's Aheadset is a simple, affordable solution for your headset needs. • Bearing Type: Cup and Cone • Color: Black • Crown Race: 26 • Defined Color: Black • Lower Stack Height: 12 mm • S.H.I.S Lower: EC30 • S.H.I.S Upper: EC30 • S.H.I.S. Stem Clamp Diameter: 25.4 • Upper Stack Height: 18 mm • Weight: 163 g

Replacement top subassemblies are compatible across Cane Creek 110-, 40-, and 10-Series headsets with the same SHIS values. - Bearings not included - Stack height = 9mm

This is the Top Cover for the Cane Creek 40 Series ZeroStack headset. Please contact us if you have any questions about which parts are correct for your headset.

With the conception of our Cane Creek eeWings Titanium crank set we cut no corners, and our CNC-machined preload assembly is no exception. The Cane Creek Crank Preloader is equipped with an aluminum preload ring, an aluminum inner thread ring, and a titanium 2.5mm hex fastening bolt. We are so proud of this piece of jewelry that we decided to design it to fit onto other 30mm crank spindles from SRAM and Raceface, and 28.99mm SRAM Dub Crank spindles. Lose the plastic preload on your crankset, add peace of mind. - 7075 Aluminum thread ring - 7075 Aluminum preload spacer adjuster - Grade 5 Titanium 2.5mm hex fastening bolt - Fits Raceface 30mm spindles, SRAM 30mm spindles, and SRAM 28.99mm DUB spindles

Super-smooth steering, quality materials, cutting-edge design and serious durability are all hallmarks of Cane Creek's 40-Series headsets. • Technical Description: EC44/40/H12/K • Bottom Type: EC - External Cup • Bottom Head Tube Inside Dia.: 44.00mm • Crown Race Seat Dia.: 39.79mm • Crown Race Type: Steel, Face-Sealed • Bottom Stack Height: 12mm • Bottom Bearing Type: Black Oxide, Sealed • Material: 6061 aluminum • Weight: 65g